P0041 code definition
P0041 tells us the ECU has detected swapped sensor signals for oxygen sensor 2 between banks 1 and 2. This code may be associated with P0040.
What the P0041 code means
P0041 means that the engine control unit (ECU) is seeing the signals for oxygen sensor 2 has switched between the left and right banks. The bank 1 sensor 2 signal is swapped with bank 2 sensor 2 causing the ECU to trigger a Check Engine Light on the dash.
What causes the P0041 code?
P0041 has a few common causes:
- Swapped connectors between oxygen sensor 2 left and right bank
- May indicate ECU failure or error
- Wiring damaged, open, or shorted
- Swapped oxygen sensor wiring between banks
Generally this code is a result of oxygen sensor replacement or repair and the connectors have been swapped.
What are the symptoms of the P0041 code?
The first symptom of P0041 is the ECU reading improper signals for bank 1 and 2 sensor 2. This causes a Check Engine Light to be displayed including a possible flashing Check Engine Light. After the code is displayed the ECU may put the car into a limp mode to prevent damage to the vehicle. Drivability issues such as poor vehicle fuel economy, engine stalling, loss of engine power, and poor running may all occur once the code is enabled.
How does a mechanic diagnose the P0041 code?
There are a few simple steps that must be taken when diagnosing P0041:
A qualified technician will hook up a scan tool to the vehicle's OBD-II port to confirm P0041 is the code present.
The freeze frame data will be observed for P0041 to see what conditions, such as vehicle speed, operating temperature, engine speed, and operating time the code was detected in, so that these conditions can be recreated on a road test.
A road test will be performed with a scan tool installed in the OBD-II port to confirm an issue is present.
The technician will visually inspect the wiring on both bank 1 and 2 sensor 2 looking for damaged wiring, broken wiring, swapped connectors, or wiring shorted to ground or power.
If the wiring passes the visual test, a continuity test will be performed with a multimeter for instance to tell us that the wiring has no breaks or shorts. This is done to rule the wiring out.
It is possible that all of these tests will be passed. If this occurs, the technician will perform a diagnostic test of the car’s ECU. These tests are specific to car makes and the manufacture will provide all steps to test the ECU.
Common mistakes when diagnosing the P0041 code
In general, this code is caused by previous repairs to the vehicle. Overlooking swapped connectors and jumping straight to ECU problems will cause test results to be faulty. Following step-by-step procedures prevents overlooking simple issues.
How serious is the P0041 code?
Though uncommon, P0041 can indicate a serious issue with the vehicle that will prevent normal and safe driving until repairs are made. This code may put the vehicle into a limp mode which prevents damage to the engine and catalytic converters. Any vehicle that is in limp mode or is running poorly should be inspected by a qualified technician before normal operation.
What repairs can fix the P0041 code?
There are a few potential fixes:
- Bank 1 sensor 2 and bank 2 sensor 2 wiring or connectors must be swapped
- Repairing or replacing any open, shorted, or damaged wiring
- Swapping wiring to the proper side
- In extreme cases, the ECU may be replaced
Additional comments for consideration regarding the P0041 code
P0041 is not a code that is seen often. Most likely it is due to repairs performed and a Check Engine Light will be present shortly after the repairs.
Need help with a P0041 code?
YourMechanic offers certified mobile mechanics who will come to your home or office to diagnose and repair your vehicle. Get a quote and book an appointment online or speak to a service advisor at 1-800-701-6230.
This article originally appeared on YourMechanic.com as P0041 OBD-II Trouble Code: O2 Sensor Signals Swapped Bank 1 Sensor 2/ Bank 2 Sensor 2 and was authored by Spencer Clayton.