• 3

Dear Tom,

Every time I hit the brake pedal, my brakes make this awful high-pitched squeal. When I stop at a light I get stares from people. It's embarrassing! I just had the brakes done last month, so why are they squealing? Help!

Melissa from Manhasset, NY


Take your car back to the shop. Sounds to me like the pad insulators, anti rattle clips, or calipers are loose. The squeal you hear is the result of vibration of the brake pads. I would not expect to be charged; this should be covered under the brake job warranty.

Melissa brings up a popular topic that needs to be addressed. Brake squeal is common and can be caused by a number of conditions: Worn pads, glazed pads and rotors, broken anti rattle clips, lack of pad insulation or insulation shims, and incorrect rotor surface cut or no surface cut at all. Let's take a closer look.

Worn Pads

A brake pad is comprised of steel backing with friction material attached to it. Application of the brakes produces hydraulic pressure that causes the brake pads (via brake calipers) to clamp down on the rotors (discs) creating friction. It is the friction of the pads against the rotors that slows and stops the vehicle. When the friction material on the pads wears down, it is time to change the pads. Some pads are equipped with a wear indicator, which is a small spring steel clip. When a pad is worn, this clip makes contact with the rotor and generates a high-pitched squeal, telling you that it is time to service the brakes. If the pad does not have a wear indicator, then when the pad has worn down to the steel backing it will grind into the rotor and need to be replaced. In this scenario, the rotor may have to be replaced as well, depending on how badly it was affected.

Glazed Pads and Rotors

Brake squeal can also occur when brake calipers stick and the brake stays partially applied. When this happens the pad is in constant contact with the rotor, producing excessive friction and thus heat. Overheated pads harden and crystallize. This glazing occurs on the rotors as well. The squealing sound is a result of these super hardened surfaces coming in contact with one another. Remember, it is the friction created by the brake pad against the rotor that stops a vehicle. When crystallization of pad and rotor occurs, there is much less friction. This results in diminished braking power and squealing brakes. At this point the pads must be replaced and the rotors resurfaced or replaced.

Broken Anti Rattle Clips

The brake pad is loosely held in place on the caliper by pad stays. An additional part called an anti rattle clip is used to secure the pad so that it will not vibrate or rattle when the brake is applied. If anti rattle clips are worn or broken, pad vibration will cause squealing. In this case, the clips must be replaced.

Lack of Pad Insulation or Insulation Shims

When a car comes from the factory, insulation shims are placed against the steel backing of the pad to insulate it from the brake caliper. This is necessary to prevent brake squeal. These shims eventually wear out or they are discarded when a brake job is performed. When the pads are replaced, either the shims must be replaced or silicone insulation gel must be applied to prevent squeal. If you had your front brakes replaced recently and they're squealing, take it back to the shop and make sure the shims were installed or gel was used.

Incorrect Rotor Surface Cut or No Surface Cut at All

When a brake job is performed, the rotors must be resurfaced to remove any glazing and return the surface to "true." First the rotor is machined to remove grooves and/or imperfection on the rotor surface. Once the rotor face is "true," a slow, non-directional finish is applied to the rotor face to ensure proper break-in of the pads. This process also insures that the pads don't ride up on the face of the rotor when braking. Riding up of the pads can cause a clicking noise, the breaking of anti rattle clips, or caliper pin wear. If the rotor is found to be too thin according to state inspection rules, it is discarded and replaced. It is important to note that if your pads were replaced without resurfacing the rotors, then squealing and pedal pulsation will probably occur.

Read More Stories from Tom Torbjornsen:

- Oil Change Every 3,000 Miles?
- Oil Changes: Where Should I Get Them Done?
- Synthetic Motor Oil: Should You Use It?

I'm reporting this comment as:

Reported comments and users are reviewed by Autoblog staff 24 hours a day, seven days a week to determine whether they violate Community Guideline. Accounts are penalized for Community Guidelines violations and serious or repeated violations can lead to account termination.

    • 1 Second Ago
      Rachel Benson
      • 5 Months Ago

      My brakes have been squeaky for a couple of months now.  I didn't know that the squeak was caused by bad brake pads or rotors.  I will am going to have to take my car to determine the extent of the repairs.  I hope I didn't do more damage by not taking my car in sooner.   <a href='http://www.expressoil.com/mechanical-services/brake-service/' >http://www.expressoil.com/mechanical-services/brake-service/</a>

      Marcus Fillion
      • 2 Months Ago

      Squealing brakes aren't just embarrassing, they're dangerous. Whenever I see people with squealing brakes, I wan to tell them to go back to the shop. It's a sign of bad pads, at the very least. If your brakes are squealing, get them checked. www.oakhollowtire.com

      Davey Hiltz
      • 5 Months Ago

      I've been wanting to avoid the problem with my squeaking breaks for a bit longer, but I'm afraid I'm going to have to fess up to it now. I hate replacing the brake pads on my car, but if I have to, I have to. I wonder how much it'll cost to get them repaired somewhere else. At the same time, I would think it would be much more worth it just to do it myself. 

       <a href='http://www.alaskanautocenter.com/services' >http://www.alaskanautocenter.com/services</a>